Used Corn Head Inspection Checklist: What to Check Before You Buy
A corn head looks like the simple end of the combine — a row of snapping units bolted to a frame. But it does the hardest job on the machine: it pulls every stalk down, strips every ear, and feeds them to the feederhouse at full ground speed. A head that looks fine in the shed can shell corn on the ground all harvest if the chains are stretched, the stalk rolls are worn, or the deck plates are set wrong.
Start with the gathering chains
The gathering chains pull stalks into the row units, and they wear faster than anything else on the head. Check every chain, row by row.
Run your hand along each chain and look for stretched links — a chain that sags between the sprockets or rides up off the teeth has run past its useful life. Check the lugs: bent, broken, or missing lugs leave gaps, and stalks slip through those gaps instead of feeding in. A few worn lugs are normal; a chain missing lugs across several rows is a head that has been run hard.
Spin the idler sprockets by hand — they should turn freely with no grinding or wobble, and hooked or chipped teeth will chew a new chain in a season. Check the tensioners, too: springs should hold tension and the arms should move freely, not rusted in place. Check the chain guides and wear strips under each chain — deep grooves let the chain wander, and a wandering chain eats lugs and sprockets.
Stalk rolls
The stalk rolls — the snapping rolls under each row unit — grab the stalk and pull it down through the deck plates so the ear snaps off. They are the heart of the head, and wear hides there.
Look at the flutes on every roll. Sharp, even flutes grip and pull; flutes worn smooth or rounded off let stalks slip, which means slow feeding and ears bouncing off the deck plates. Check for broken or bent flutes, and for rolls that have been welded or built up — a repair that changes the roll diameter changes how that row feeds.
Grab each roll and try to move it side to side and up and down. Any play means a worn bearing, and a bearing that fails in the field takes the roll and the gearbox with it. Spin each roll by hand — it should turn smoothly with no grinding or catching. On knife rolls, dull or chipped knives tear stalks instead of cutting them, and on chopping heads, missing or broken chopping knives leave long stalk pieces that plug the head and the combine.
Deck plates
The deck plates are the two flat plates on either side of each row, with a gap between them that the stalk slides through. The gap is everything — too wide and ears slip through and fall to the ground; too narrow and stalks jam.
Check that the gap is even from front to back on every row. A gap that wanders along the row means bent plates or a worn adjustment mechanism. Look for plates that have been hammered straight, welded, or shimmed — all signs of a head that has fought rocks or rough ground.
Work the deck plate adjustment on each row. It should move smoothly through its range and hold its setting — an adjustment that slips, sticks, or has a stripped handle means the row can't be set right in the field. On hydraulically adjusted heads, cycle the adjustment and check that every row moves together; one row lagging behind points at a cylinder or linkage problem.
The auger
The cross auger gathers the ears from every row and feeds them into the feederhouse. Check the flighting along its full length: bent flighting, flighting worn thin at the edges, and flighting that has been patched or re-welded all feed unevenly and can leave ears piling up at one end.
Check the retractable fingers in the center of the auger. Each finger should extend and retract smoothly as the auger turns — a finger stuck out will drag and break, and a finger stuck in won't feed the center rows. Spin the auger by hand and watch the fingers cycle. Check the auger bearings at both ends and the center support if it has one: grab the auger and rock it — any play means wear, and a bearing that seizes mid-harvest stops the whole head. Look at the auger trough for dents and packed residue — dented troughs catch ears, and buildup hides rust.
Row-unit gearboxes and drive
Every row unit has a gearbox driving the stalk rolls and gathering chains, and they all run off a common drive from the combine. Check the oil in each gearbox if it has a check plug or sight glass — full and clean is what you want, milky means water, and low oil with no visible leak means it has been run dry. Trace the main drive from the combine connection to the head: check the drive shaft, universal joints, and any slip clutch. Joints should have no play, the shaft should slide freely in its splines, and the slip clutch should not be rusted solid — one that can't slip turns a slug of stalks into a broken gearbox. Check the main gearbox for leaks and cracked housing, and look at the drive belts or chains on belt-driven heads for cracking, glazing, and proper tension.
Frame, header height, points, and dividers
A corn head has no reel, but the points and dividers at the front of every row do the guiding. Check every point: bent, cracked, or missing points let stalks push aside instead of feeding in.
Cycle the header height control — the head should raise and lower smoothly and hold its height. On heads with automatic height control, check the sensors and feelers: bent feelers, broken sensor arms, and frayed wiring all mean the head won't follow the ground. Sight down the frame from the end: it should be straight, with no sag in the middle and no twist. Check the mounting points where the head hooks to the feederhouse — cracked welds or wallowed pin holes here mean the head won't sit square on the combine, and a head that sits crooked feeds crooked.
The live test: run it in standing corn
Everything above is preparation. The real test is running the head in standing corn, and on a serious purchase it is worth asking the seller to run the combine in the field.
Watch the head from the cab and from the ground. Stalks should feed smoothly into every row with no bunching, and ears should snap off cleanly and ride the auger to the center. Ears bouncing off the deck plates point at worn stalk rolls or a deck plate gap set too wide. Stalks piling up at the auger point at flighting wear or a finger problem.
Walk behind the combine after a pass and count the ears on the ground. A steady trail under one or two rows points at those specific row units — chains, rolls, or deck plates — while ears scattered across the whole width point at a head set wrong or worn evenly across.
Listen as it runs. Knocking or grinding from a row unit is a gearbox or bearing telling you it is done. A head that plugs in normal corn has a feeding problem — chains, rolls, or auger — and one that plugs only in down corn may just need the points and dividers set right. Check the combine's loss monitor against what you see on the ground: a monitor that reads clean while ears litter the ground is a monitor that has been turned down.
Ask for the history
Ask for service records: chain replacements, stalk roll work, gearbox oil changes, auger repairs. Ask how many acres per year it covers — a head that runs a few hundred acres a year has lived easier than one that runs thousands. Ask how it is stored: inside versus outside is one of the biggest predictors of remaining life on chains, bearings, and gearboxes. Ask whether it matches your combine — header width, feederhouse size, and drive connection all have to fit. Run the serial number past the dealer for recalls or warranty history — a five-minute call that can turn up things the seller didn't mention.
Screen a used corn head before you drive out
The Used Equipment Analyzer lets you upload photos of a machine you're considering and get an AI inspection report flagging visible wear, damage, and red flags — before you burn a day on the road.
Run a photo inspection — $29The bottom line
Chains tight with full lugs, stalk rolls with sharp flutes and no play, deck plates even and adjustable, an auger with straight flighting and working fingers, gearboxes full of clean oil, a straight frame with sound points, and a clean run in standing corn with few ears on the ground — that's the inspection. Anything you find becomes the negotiation; anything you skip becomes the surprise in October.
Run through this list, run it in corn, and buy the head you actually checked — not the one you hoped was in the photos.
